DPA 5006A

DPA 5006A

Artiklinumber: IDS0048140

This is a complete Surround Kit with five carefully factory-matched omnidirectional microp...

Laoseis / Tarneaeg info
store

Ajutiselt otsas

local_shipping

Ajutiselt otsas. Teavituseks klõpsake »

warehouse

Ajutiselt otsas tarnija laos

Tarneaeg on meie hinnanguline aeg, mille jooksul saame kauba teile kohale toimetada kas meie enda või välise lao kaudu. See on ainult hinnanguline ja tarneaega võivad mõjutada mitmed tegurid, mis on meie kontrolli alt väljas. Jätame endale õiguse võimalikele viivitustele, läbimüügi lõppemisele ja muudatustele. Samuti jätame endale õiguse muuta tarneviisi, kui tellimus on teie valitud tarneviisi jaoks liiga suur või raske. Saate SMS-i või e-kirja, kui teie pakk on teie valitud pakiautomaadis või esinduses kättesaadav. Kui valisite kojuveo, saadetakse teile eelnev teavitus, et leppida kokku tarneaeg. Kui soovite kauba poest ise järele tulla, olete oodatud pärast SMS-i saamist, et teie tellimus on valmis.

12419.00 EUR/tk

Payment
EAN: 5713055000219 MPN:

Teised, kes ostsid DPA 5006A ostsid ka

This is a complete Surround Kit with five carefully factory-matched omnidirectional microphones. Even though the standard tolerances on the d:dicate™ 4006A Omnidirectional Microphones are extremely low, the surround match is even closer.

The specially selected d:dicate™ 4006A Omnidirectional Microphones are matched within ±0.5 dB on both frequency response and sensitivity from mean of set.

The natural sound, high sensitivity, low noise-floor and extremely linear frequency response from 10 Hz to 20 kHz (±2 dB) of the microphones make the d:dicate™ 4006A Omnidirectional Microphones the perfect choice for all AB Stereo, Decca Tree or surround main array recordings. The precise reproduction, total transparency and natural-sounding clarity of d:dicate™ 4006A Omnidirectional Microphones will provide you with a lifetime of satisfying listening.

The foam design in the heavy-duty transportation box allows for fast and easy exchange of microphone/accessory inlays.

Directional pattern
Omnidirectional
Principle of operation
Pressure
Cartridge type
Pre-polarized condenser
Frequency range
10 Hz - 20 kHz
Frequency range, ±2 dB
10 Hz - 20 kHz
Sensitivity, nominal, ±2 dB at 250 Hz
40 mV/Pa; -28 dB re. 1 V/Pa
Equivalent noise level, A-weighted
Typ. 15 dB(A) re. 20 µPa (max. 17 dB(A))
Equivalent noise level, ITU-R BS.468-4
Typ. 27 dB (max. 29 dB)
S/N ratio (A-weighted), re. 1 kHz at 1 Pa (94 dB SPL)
Typ. 79 dB(A)
Total harmonic distortion (THD)
< 1% up to 139 dB SPL peak
Dynamic range
Typ. 124 dB
Max. SPL, peak before clipping
146 dB
Switchable attenuator, filters etc.
0 dB / -20 dB
Output impedance
200 Ω
Minimum load impedance
2 kΩ
Cable drive capability
100 m (328 ft)
Output balance principle
Impedance balancing with Active Drive
Common mode rejection ratio (CMRR)
> 60 dB
Power supply (for full performance)
48 V Phantom power (± 4 V)
Current consumption
2.8 mA
Connector
XLR-3M. Pin 1: shield, Pin 2: signal + phase, Pin 3: - phase
Color
Matte black
Weight
163 g (5.7 oz)
Microphone diameter
16 - 19 mm (0.6 - 0.75 in)
Capsule diameter
16 mm (0.6 in)
Microphone length
170 mm (6.7 in)
Maximum output voltage, RMS
8 V
Polarity
+V at pin 2 for positive sound pressure
Temperature range
-40°C to 45°C (-40°F to 113°F)
Relative humidity (RH)
Up to 90%
Matching tolerance (frequency response and sensitivity)
±0.5 dB
Phase deviation for kit
< 5°