dj service
shopping_cart
DPA 4018FGT

DPA - 4018FGT

Artnr: IDS0048115
Tarneaeg: Kaup on ajutiselt otsas. Kontakteeruge meiega tarneaja prognoosiks. »

DPA
4478.00 EUR/tk

Igakuine kuumakse alates 117.54 euro

Teave:

A complete twin supercardioid microphone floor stand solution in the modular d:dicate™ Microphone Series offering a high-quality stage voice or instrument mic.

The floor stand has an elegant and exclusive design with a black, non-reflective surface specifically made to handle the, from time to time, rough life in TV-studios, OB-vans and onstage in theaters and concert halls. The Floor Base has an integrated shock mounting solution. The thread screw holds the Stand Extension and Active Boom Pole. This unique design allows for a long stage microphone boom pole that does not swing, but rapidly stabilizes itself after being positioned.
 

This floor stand solution comes in one length:

d:dicate™ 4018FGT Supercardioid Microphone, Single 122 cm (48 in) Boom, Floor Stand
 

The microphone capsule

The supercardioid shape is frequency independent, securing an identical sound color around the microphone. The usual rear lobe heard on most supercardioids is minimized on this capsule. This makes it much more isolated without sudden frequency dependent peaks and dips.
 

A truly flexible range

This mic is part of the flexible d:dicate™ Microphone Series. At any time, and with no tools needed, it is possible to transform the d:dicate™ 4018F Supercardioid Microphone into a new configuration. You can combine it with another d:dicate™ or d:facto™ Microphone Capsule or Preamplifier.

Directional pattern
Supercardioid
Principle of operation
Pressure gradient
Cartridge type
Pre-polarized condenser
Frequency range
20 Hz - 20 kHz
Frequency range, ±2 dB, at 30 cm (11.8 in)
40 Hz - 18 kHz
Sensitivity, nominal, ±2 dB at 1 kHz
12 mV/Pa; -38.4 dB re. 1 V/Pa
Equivalent noise level, A-weighted
Typ. 16 dB(A) re. 20 µPa (max. 19 dB(A))
Equivalent noise level, ITU-R BS.468-4
Typ. 23 dB
S/N ratio (A-weighted), re. 1 kHz at 1 Pa (94 dB SPL)
Typ. 78 dB(A)
Total harmonic distortion (THD)
< 1% up to 137 dB SPL peak
Dynamic range
Typ. 121 dB
Max. SPL, peak before clipping
142 dB
Output impedance
100 Ω
Minimum load impedance
2 kΩ
Cable drive capability
100 m (328 ft)
Output balance principle
Impedance balancing
Common mode rejection ratio (CMRR)
> 40 dB
Power supply (for full performance)
48 V Phantom power (± 4 V)
Current consumption
3.5 mA
Connector
XLR-3M. Pin 1: shield, Pin 2: signal + phase, Pin 3: - phase
Color
Matte black
Microphone diameter
19 mm (0.75 in)
Capsule diameter
19 mm (0.75 in)
Microphone length
Capsule: 23 mm (0.9 in), Boom pole: 122 cm (48 in)
Maximum output voltage, RMS
2.2 V
Polarity
+V at pin 2 for positive sound pressure
Temperature range
-40°C to 45°C (-40°F to 113°F)
Relative humidity (RH)
Up to 90%
Matching tolerance (frequency response and sensitivity)
±1 dB
Phase deviation for kit
< 10°