Palmer - Supreme Soaker

Artnr: IDS0124502
Tarneaeg: 6-14 tööpäeva.

Teave:

Analog Dynamic Tube Amp Hub

Reactive attenuator and load box
Finely-tuned analogue speaker simulator
Speaker output with unique tone control
Microphone / line input (blendable with speaker simulator)
Front panel headphone output
Stereo FX loop
Front panel aux input
Balanced stereo XLR Line Outputs
Compatible with 8 and 16-ohm setups
Rated for tube amps up to 150 Watts
Amp protection circuit with permanent amp load
All analogue experience; no app required!

Specifications

General
Product type attenuator, DI box, Headphone Amp:, load box, Microphone preamplifier, power soak, Re-amping device analogue, speaker simulator
Signal processing Analog
Front panel controls 7-Step Speaker Attenuation, Aux In Level, Hard/Soft Tone Selector, Line EQ (5 Voicings), Line Out Blend, Line Out Level, Mic Gain, MIC Tone, Phone Level, Pre/Post Switch (Amp to Line Out), Speaker Tone (5 Voicings)
Rear panel controls Amp Load Impedance Switch, FX Level (Pro/Instrument), FX Loop Line Out, FX Loop Re-Amp, GND/Lift, MIC/LINE Input PAD, Phantom Power, Polarity
Number of inputs 5
Input type Balanced, Unbalanced
Input connectors 3.5 mm jack, 6.3 mm jack, XLR
Number of outputs 6
Output type Balanced, Unbalanced
Output connectors 3.5 mm jack, 6.3 mm jack, XLR
Ground/lift switch Yes
Transformer isolated outputs Yes
Internal load impedance 16 ohms, 8 ohms
Minimal load in OFF status 16 ohms
Max input handling 150 W
Power attenuator 7-step
Voicing filter 5-step Speaker Tone and 5-step Line EQ
Indicators bypass, Full attenuation, input level, MIC-Signal/Clip, Output level, power soak, thermal overload
Power supply + 9 V DC barrel jack - 1.5 A
Power supply polarity Center negative
Power connector 2 x 5.5mm
Maximum power consumption 13.5 W
Standby power consumption 0.3 W
Dimensions (W x H x D) 334 x 108 x 274 mm
Weight 6,6 kg
Ambient temperature (in operation) - 20°C - 25 °C
Relative Humidity < 80 % ( non-condensing )
Accessories (included) Power supply

Audio inputs
AUX IN max. input level (< 1% THD, 1kHz) + 9 dBV
AMP IN max. input power 150 W Peak, 100 W RMS

Audio outputs
LINE OUT max. output level (<1% THD) + 18 dBu
RE-AMP max. output level (<1% THD) + 1.5 dBv
PHONES OUT max. output level (<1% THD, 1kHz) 1.4 V RMS
PHONES OUT min. impedance 33 Ohm

MIC / LINE Input
MIC / LINE IN low cut frequency (-3dB) 90 Hz
MIC IN max. gain 58 dB
MIC / LINE IN Gain range 0 - 25 dB
MIC IN (XLR) max. input level (< 1% THD, 1kHz) + 1 dBu
LINE IN (TRS) max. input level (< 1% THD, 1kHz) + 22 dBu
MIC IN to LINE OUT THD+N (1kHz, +4dBu) < 0.006 %
MIC IN to LINE OUT THD+N (20Hz-20kHz, +4dBu) < 0,04 %
MIC IN to LINE OUT EIN (max. gain, unweighted) - 114 dBu
MIC IN to LINE OUT SNR (all bypass) 105 dB
MIC/LINE IN PAD attenuation 20 dB
MIC IN (XLR) input impedance (balanced) 1500 Ohm(s)
LINE IN (TRS) input impedance (balanced) 24000 Ohm(s)